Eldes ET082 User Manual

ET082GSM/GPRS COMMUNICATOR

1010 ENET082 GSM/GPRS COMMUNICATOR5. CONFIGURATION METHODS5.1. SMS Text Messages!!! In this user manual the underscore character ”_” represents one s

1111ENET082 GSM/GPRS COMMUNICATOR5.2.3. Ending the Conguration Process After the system conguration is complete, use one of the following methods t

1212 ENET082 GSM/GPRS COMMUNICATOR6. COMMUNICATION WIRING METHODSET082 communicator supports one of the following communication wiring methods:• RING

1313ENET082 GSM/GPRS COMMUNICATOR1. Connect the communicator’s RING and TIP terminals to the alarm panel’s RING and TIP terminals respectively.2. Co

1414 ENET082 GSM/GPRS COMMUNICATOR6.2. Keybus InterfaceATTENTION: This communication wiring method is supported by hardware version ET082-30 and up.N

1515ENET082 GSM/GPRS COMMUNICATOR7. COMMUNICATION MODES AND METHODSET082 communicator supports Basic and Advanced modes and methods providing a variet

1616 ENET082 GSM/GPRS COMMUNICATORCommunication wiring method?RING/TIP KeybusPSTN line is being supervised by ET082 in case it is cut-oSet by PCB jum

1717ENET082 GSM/GPRS COMMUNICATOR7.1. Basic ModeThe communication method of Basic mode is selected by jumper position on the SET/MODE pins on board.

1818 ENET082 GSM/GPRS COMMUNICATOR4. On ET082: Ensure that NO jumpers are set on SET/MODE pins on board. SETMODE105. If required to override the Acc

1919ENET082 GSM/GPRS COMMUNICATOR4. On ET082: Set a jumper on SET pins on board. SETMODE125. On ET082: Connect the device to the computer via USB ca

22 ENET082 GSM/GPRS COMMUNICATORUser Manual v2.1Valid for ET082 v01.12.00 and up; hardware version: ET082-30 and up.SAFETY INSTRUCTIONS Please read an

2020 ENET082 GSM/GPRS COMMUNICATORin order to reduce the data trac consumption.• Protocol – Format of the data message transmitted from ET082 to the

2121ENET082 GSM/GPRS COMMUNICATOR7.2.1. Voice Calls MethodBased on the communication wiring method that is being used, using this method the communica

2222 ENET082 GSM/GPRS COMMUNICATOR6. On ET082: Open Messaging Settings section and proceed as follows:a. Set up to 5 user phone numbers that will be

2323ENET082 GSM/GPRS COMMUNICATORsection. For more details, please refer 9. MONITORING STATION PHONE NUMBER AND ACCOUNT REPLACEMENT* Necessary only

2424 ENET082 GSM/GPRS COMMUNICATOR8. GSM MODEM SETTINGSVoice Calls communication method might partly or completely fail with some alarm panel models d

2525ENET082 GSM/GPRS COMMUNICATOR10. SMS PASSWORDFor security reasons, the device uses the following type of password:SMS password – 4-digit password

2626 ENET082 GSM/GPRS COMMUNICATOR12. INPUTSThe system comes equipped with 3 inputs identied as Z1, Z2 and Z3. The inputs are designed for dierent d

2727ENET082 GSM/GPRS COMMUNICATORTo manage input alarm and restore data reports and set the Account number, please refer to the following conguration

2828 ENET082 GSM/GPRS COMMUNICATOR13. OUTPUTSThe system comes equipped with 3 open collector outputs identies as C1 through C3 designed for electrica

2929ENET082 GSM/GPRS COMMUNICATORTurn ON output for time periodSMSSMS text message content:ssss_Co:ON:time or ssss_out-name:ON:timeValue: ssss – 4-dig

33ENET082 GSM/GPRS COMMUNICATORContents1. GENERAL INFORMATION ...

3030 ENET082 GSM/GPRS COMMUNICATOR• GSM Restored – The output action will be carried out in case the GSM connection is restored. For more details on

3131ENET082 GSM/GPRS COMMUNICATOR14. PSTN CONNECTION STATE MONITORINGNOTE: This section applies to With PSTN Line Supervision and With External PSTN L

3232 ENET082 GSM/GPRS COMMUNICATOR15. GSM CONNECTION STATE MONITORINGThe device supervises the GSM connection every 10 minutes. When the GSM signal is

3333ENET082 GSM/GPRS COMMUNICATOR17. PERIODIC TESTThe device comes equipped with periodic test data report transmitted under CID event code 602 to the

3434 ENET082 GSM/GPRS COMMUNICATOR20. TECHNICAL SUPPORT20.1. TroubleshootingIndication Possible Reason GSM LED is o or not ashing • No external pow

3535ENET082 GSM/GPRS COMMUNICATOR21. RELATED PRODUCTS Plastic enclosure Power supply Magnet mount straight GSM antenna. Adhesive at GSM antenna Smart

3636 ENET082 GSM/GPRS COMMUNICATOR

3737ENET082 GSM/GPRS COMMUNICATOR

3838 ENET082 GSM/GPRS COMMUNICATOR

3939ENET082 GSM/GPRS COMMUNICATOR

44 ENET082 GSM/GPRS COMMUNICATORIt is strictly forbidden to copy and distribute information in this document or pass to a third party without an advan

Made in the European Unionwww.eldes.lt

55ENET082 GSM/GPRS COMMUNICATOR1. GENERAL INFORMATION ET082 is a micro-controller based device intended to replace the third-party PSTN/non-GSM alarm

66 ENET082 GSM/GPRS COMMUNICATOR2.2. Main Unit, LED Indicator and Connector FunctionalityOPENJP9JP8L1 L2 L4 C1RING DC+TIP COM C2 C3Z2 Z3Z1 COMF1SETDE

77ENET082 GSM/GPRS COMMUNICATOR2.4. Wiring Diagrams2.4.1. General WiringL1 L2 L4 C1RING DC+TIP COMC2C3Z2 Z3Z1 COMALARM PANELOR OTHER APPLIANCEAUX++1

88 ENET082 GSM/GPRS COMMUNICATOR3. INSTALLATION• The device can be installed in a metal or non-ammable cabinet only.• The device should be installe

99ENET082 GSM/GPRS COMMUNICATOR4. GENERAL OPERATIONAL DESCRIPTIONET082 communicator is used with third-party PSTN/non-GSM alarm panels as a communicat