Eldes ESIM251 User Manual download pdf (Page 28)

Type of control

via call

1,2,3,4,5 and 0

When users

No:1,2,3,4,5 call the

output is enabled.

The rst digit refer to user number. The second

digit refers to command. Therefore to set a

possibility for user NO1 to enable the relay via call

you have to use the command MS10

1,2,3,4,5 and 1

When users

No:1,2,3,4,5 call the

output is disabled.

MS11

The rst digit refer to user number. The second

digit refers to command. Therefore to set a

possibility for user NO1 to disable the relay via call

you have to use the command MS11

1,2,3,4,5 and 2

When users

No:1,2,3,4,5 call

output status is

changed(TOGGLE)

The rst digits refer to user number. The last digit

refers to command. Therefore to set a possibility

for user NO1 to enable the relay by one call and

thendisableitbythenextcallyouhavetosethe

command MS12

Setting relay

impulse

duration

1,2,3,4,5 and

Th.m.s

Setting relay impulse

duration for users

No:1,2,3,4,5. h- hours,

m- minutės, s-

seconds.

E. g. to set the timer for 5 hours 10mins 3seconds

for user NO1 you have to use the command

MS1T5.10.3

This means that when afore mentioned user NO1

control the relay via call the impulse duration is

5hours 10mins and 3seconds and after this period

the relay returns to the previous status.

Example of SMS message conguring C1 output:

This message congures C1 output parameters.

CE1234 meansthatС1outputcanbecontrolledbyusersNO1-NO4(NO5cannotcontrolviacall).

CS123 means that only users NO1, NO2 and NO3 will receive conrmation call.

MS10 means that when user NO1 calls the system he/she enables C1 input, but cannot disable it via call. The user can disable it via

SMS message if he/she knows the password.

MS42meansthatwhenuserNO4callsthesystemhe/shewilleitherenableordisableoutputC1(TOGGLEmodeison).Itdepends

on the relay status before making a call.

MS1T0.0.40 means that when user NO1 call the relay is turned on for 40seconds and then it automatically turns o.

To see the preset values for any command send SMS message with the same format that you use when changing parameters; only

Value structure will have no value. This does not apply to MS and CT commands. When requesting MS and CT parameters MS and

CTmustbefollowedbyonecharacter–usernumber(1,2,3,4or5).:

XXXX–userpassword.ValuestructureisCn,whereCniscommandname(2letters).

E. g. XXXX_SMSEXTRA:COC:CE,CS,MS1,MS3

3.9.2.2 Settings of the output controlled by SMS messages

This chapter describes the ways of informing users when they are trying to enable/disable the relay via SMS messages described in

chapter 3.6. Parameters are changed by sending the following SMS message to system ESIM251:

XXXX–userpassword.ValuestructureisCnVal,whereCniscommandname(2letters),andVal-itsvalue(digitswithoutspacesor

punctuationmarks).

XXXX_SMSEXTRA:COC:CE1234,CS123,MS10,MS42,MS1T0.0.40

XXXX_SMSEXTRA:COC:Value1,Value2,……,ValueN

XXXX_SMSEXTRA:OCS:Value1,Value2,……,ValueN

FOR ADVANCED USERS

All these features can be congured using program “ELDES Conguration Tool“

1 2 ... 23 24 25 26 27 28 29 30 31 32 33 34 35 36

Comments to this Manuals

No comments

Eldes ESIM251 User Manual Page 28

Comments to this Manuals